Відео

Just channel lock it and I used a big flathead screw driver and hit the channel locks. It came off Finally. Wasn't easy I admit but wasn't as hard as I thought it was going to be. Chanel locks I had on tight as I could squeeze them

Spray some used motor oil inside that x-member to keep it from rusting.

I would love to learn how to weld. I have a 1993 Buick Century that is like your car perfect and clean except for a couple of spots. It has similar rust repairs needed. Good video.

Here is another tip. When replacing the filter clean the hole in the transmission with a shot of brake clean so there is no oil and the rubber ring has a better grip. Then use green Lube Gard assemblee goo on the contact points of the filter to the valve body. This will hold the filter in place until you can get the pan on. Put the assemnlee goo in the refrigerator for a few hours to make it extra sticky. This product is made to be used in automatic transmissions and will dissolve in transmission fluid. For some reason Ford could not put a screw in the filter to hold it in place. They probably saved 15 cents per transmission by doing this.😑

I wish I watched this before I broke the screw extractor 😢

Thank you. My car has a different issue. The driver side lock doesn’t lock with the remote. We get around by doing it manually from the back door. Is there any easy fix to it ? The dealer wants too much money to fix it.☹️

Also here is a tip if you are not into transmission fluid waterfalls. Drill a 1/4-inch hole in the bottom of the pan first, then remove the dipstick, and let the fluid drain out into a pan for an hour or two. Then remove the pan, replace the filter, clean the pan and magnet. Plug the hole you drilled with JB weld, let it set up and replace the pan. Refill with the same amount of fluid you drained out. A cleaner job without all the mess.😊

I have watched several of these videos and many comments state that they would drain out 5 1/2 quarts of fluid and have to install 7 quarts of fluid to get the proper fluid level. So does this mean that the factory under filled the transmission? Or is the transmission now being over filled? Kind of odd there could be such a difference. There is some fluid in the filter but not that much. Also, I have found that welders gloves help when checking the fluid level.

A couple of things about chickens and nesting. Yes, they do not mind (possibly even prefer) nesting together. However, if you have a strong pecking order in the flock, have at least one separate box or compartment for those at the bottom of the pecking order. For your nesting box, just the one divider in the middle, would have been fine. Yes, they like to roll other eggs under themselves, this is common. Sort of like an inbuilt habit. The bit of tin you put on the top is a bad idea. They tend to jump up on things, and would therefore cut their feet and get infected.

Good deal. Thanks

Amazing job, I have the same boat. Too bad the triple backflips were off cam.

Thank you. Who designs those things... surely ergonomics and comfort should be big on the list.

Im hoping this works for me because im in the same boat. Thank you for posting the extremely helpful video ☺️👍

This looks like the situation I have now, But my hole is directly underneath the O2 sensor, and the flex pipe is starting to go.😢

Thanks that was super helpful and I really appreciate the visual demo.

Ypu cant use pressrue treated plwood in an aluminum boat or you will destroy it. This is not a good idea, you are better off using regular pywood than this. But really they make marine geade plywood juat for this purpose,and other than replacing your wood floors with more aluminum, marine pkywood is the only good solution to rotten floors.

I think they adjust these newer headrests for the new gen of kids with forward head posture because of always being on their phones

Thank you, nice 👍

reset the springs. It takes 30 seconds and anyone can do it.

I still think removing the trans line and allowing it to pump out is worthwhile... It was able to pump out a little less than 4 quarts...

My 2020 f250 drives Me f... nuts! The headrest are definitely getting adjusted

Good idea on brake light check

Excellent video!!!As a side note, Bug was heard saying: Hey, Mister, can you please go somewhere else to do your teaching videos??? I'm living up to my pest expectation... Don't make it harder to get inside!!🐞🐞🐞🪲🐛

What the heck is all that clicking noise!!!!???! 😡😡😡

Why didnt you run power to the solenoid to see if it moves in and out?

Just came across your channel 👍 What lower end scanner do you like that can analyze the powerbalance, VCA bank 1&2, etc for troubleshooting?

Next stop Gold Slucing!

American Standard Canadian Cadet Toilet

wow, pretty sure thats the same engine as my Ford 1320!

i believe pressure treat wood will eat up a boat, so just use plain ply wood an put resin on top to make it water proof.

Super

Car

what are your thoughts on just putting the 3/4 plywood all the way to the back? I have another soft spot over the gas tank. it's not terrible, i'm 300 pounds and i can walk on it but it definitely flexes and the carpet and gel coat on top are rubbed away exposing the old wood.

cheapass crap made under brand names in China

Thanks for showing the cable routing, and pointing to everything. Put Rhino 700 in the video title if you can, it should get you more views!

I took my glass apart and when I did the springs fell out . Any clue how to get them back attached to hinge . Or would you have to replace . Nothing looks broke just spings fell off so door isn't closing at all. 😒

I just love how you literally skip the hardest part to do in the whole job! I'd bet 900 of the thousand views you've got are to watch how you installed the snap ring and you skip it and show it done and explain how you did it that's not how you make videos of how to do something!!!!

Nice!

This is the best alignment video i can find, you're the man.

I had a broken wheel on the bottom of a slider wheel. The wheel is spring loaded with coiled spring. I could not find this type on the tube. However, this video helped in adjusting the top and bottom tension screws well enough to operate the slider smoothly. Thank you very much for this video.

I thought I was the only one that was complaining about this horrible headrest design 😅

I like it! For the older boats that aren’t worth dumping tons of money into this is the way to go.

For the amount of work, just get a new sway bar with new links and bushings unless you really don't value your time. Boss 302 set for the rear with already mounted links and new bushings is $150-175 and comes complete.

Nice watching you work thru that. Any update? I would have thought that 12” of runway would let the egg build up too much momentum to not break the eggs

Nice job.

You did well removing the bend, however the inside bead where the rubber tire bead meets the aluminum wheel needs inspection and possibly a rasp file or emery cloth rubbed completely around the repaired area otherwise mounting a tire on an uneven and rough surface e will surely create a slow leak that will empty the air in your tire in a couple days!

I need to make a U shape but more like no rounded ends all 90* degree so it can go from the front of the house gutter immediately around the house (1” away) but it’s a 90* degree corner & all the bendy ones don’t turn sharp enough since I buried the corrugated pipe up against the house how can I do this they don’t sell this piece I’ve been looking for months

Excellent video. Thank you.

Just dumb, without a solid measurement, a Story stick as a guide to show how far. So sick of eyeballers/ 150 celcius is a joke also not even enough to bother paper. Just no experience might as well be cold Propane to 700 F. Pressure of a jack is less harmful/ Fracture as you may

To close the gap, cut a short piece of pipe and snap it over the gap.